About this part
The 06E103547P Oil Separator is a brand new genuine OEM crankcase breather valve that separates engine oil from the ventilation air on the 2.4, 2.8 and 3.2 FSI V6 engines used across the Audi A4, A5, A6, A7 and Q5 ranges. It sits under the intake manifold and controls the flow of crankcase vapour back into the intake, so a healthy unit keeps the engine breathing correctly while stopping oil mist from being drawn into the combustion chambers. The housing carries the Audi rings and the 06E 103 547 P moulding shown in the photographs, and this listing is for the real part photographed for this store, not a library picture and not a used take off. A failed separator is a common cause of rough idle, rising oil consumption, oil contamination in the intake tract and lean running faults on these FSI engines, so replacing it with the correct OE revision restores the designed crankcase pressure control.
Oil separator — one brand new genuine OEM crankcase breather valve, OE number 06E103547P, for the 2.4, 2.8 and 3.2 FSI V6 engines of the Audi A4, A5, A6, A7 and Q5.
OE/OEM Part Number:
06E103547P, 06E 103 547 P, 06E103547, 06E 103 547, 06E103547A, 06E 103 547 A, 06E103547E, 06E 103 547 E, GATES EMH9001, HENGST FILTER AS354M02, ELRING B21.010, VAICO V10-3502, MAXGEAR 18-1278, METZGER 2385119, PIERBURG 7.13498.01.0, Frankberg 5481FB0052603, TOPRAN 116 316, ABAKUS 053-028-103
The P suffix is the current VAG revision of this separator family. Earlier 06E103547, 06E103547A and 06E103547E units are listed by catalogues as the preceding versions for the same FSI V6 engine family, and the aftermarket boxes the matching unit under the references shown above. When your old part carries one of those numbers, compare the housing outline, hose ports and electrical connector with the photographs before ordering. If the number on the old part is a different base number, or if your VIN points to a different engine, send us the VIN and a photo of the old separator and we will check it against stock before the order is packed.
Why this separator gets replaced
Inside the housing, a diaphragm and a labyrinth style oil separator strip oil droplets out of the crankcase vapour before the air is metered back into the intake. Heat, oil contaminants and age harden the diaphragm and the valve seats. Once the diaphragm splits or the pressure regulating valve sticks, the crankcase either pulls too much vacuum or cannot vent at all. Typical signs are an uneven or hunting idle, a hissing noise from the intake area, oil being drawn into the intake and burned, blue smoke on acceleration, a rising oil level reading that does not match the dipstick, and lean fault codes such as P0171 or P0174 caused by unmetered air entering the system. In cold climates, moisture can freeze in a worn valve and produce a sudden rough run or a high idle. Continued driving with a failed separator can also pressurise the crankcase and push oil past crankshaft and camshaft seals, which turns a modest parts job into a much larger leak repair.
What this part is, and what it is not
This listing is the complete oil separator and pressure control valve housing 06E103547P for the 2.4, 2.8 and 3.2 FSI V6 engines. It is NOT a cylinder head or valve cover, NOT a breather hose, NOT the small diaphragm repair kit, NOT the ignition coil cover and NOT a universal catch can. It is also NOT the crankcase valve used on the 1.8 or 2.0 TFSI four cylinder engines and NOT a part for the 4.2 FSI V8 or the V6 TDI engines, even though those cars may use a similar looking plastic housing. The photographed unit has the wide irregular flange with multiple bolt ears, the round diaphragm cover, the pale service panel and the electrical connector at one end. Compare all four features with your old part before ordering.
Technical specification and what is in the box
Part number: 06E103547P, spaced label form 06E 103 547 P. Type: genuine OEM oil separator and crankcase breather valve, sometimes catalogued as an engine block breather valve or PCV valve. Application: Audi 2.4, 2.8 and 3.2 FSI V6 petrol engines of the model years in the table. Construction: moulded polyamide housing with integrated diaphragm valve and oil separation chamber, electrical connector, hose ports and multiple mounting ears. Catalogue dimensions are around 346 x 190 x 128 mm, and catalogue opening pressure for this family is around 0.03 bar or 30 mbar, though suppliers quote different values, so the number on the old unit is the final authority. Supplied: ONE oil separator assembly as photographed. Not supplied: separate gasket set, breather hoses, bolts, tools or installation labour. Approximate packed weight is 1.1 kg.
Check before you buy
Four checks prevent a wrong order. First, read the number on the old separator: 06E103547P or the earlier 06E103547, 06E103547A and 06E103547E revisions. Second, confirm that the car has one of the 2.4, 2.8 or 3.2 FSI V6 engines listed, not a diesel and not a four cylinder TFSI, because adjacent model years used several different breathers. Third, compare the housing shape: the round diaphragm cover, the pale side panel, the hose neck at one end and the position of the electrical connector must match. Fourth, check whether your old part has the same number of bolt ears and the same hose port diameters. If the VIN data, the catalogue and the old part disagree, the old part wins. Send us a photo and the VIN and we will confirm the number before dispatch.
Vehicle fitment
Part number 06E103547P belongs to the crankcase ventilation system of the naturally aspirated FSI V6 engine family used in Audi models from the middle 2000s into the middle 2010s. The table lists the applications published by parts catalogues together with the engine context that matters. Rows marked VIN check are catalogue level claims where the exact market specification has not been confirmed, so treat them as a prompt to verify against engine code, build date and the old part. When VIN data, this table and the number on the old separator disagree, the old part wins.
| Brand | Model | Year | Engine and notes |
|---|---|---|---|
| Audi | A4 B7 (8E) | 2004 – 2008 | 2.4 / 2.8 / 3.2 FSI V6, crankcase breather |
| Audi | A4 B8 (8K) | 2008 – 2015 | 2.4 / 2.8 / 3.2 FSI V6, common fitment |
| Audi | A4 B8 Avant | 2008 – 2015 | 2.8 / 3.2 FSI V6, common fitment |
| Audi | A5 B8 Coupe (8T) | 2007 – 2015 | 2.4 / 2.8 / 3.2 FSI V6 |
| Audi | A5 B8 Sportback (8T) | 2009 – 2015 | 2.8 / 3.2 FSI V6 |
| Audi | A5 B8 Cabriolet (8F) | 2009 – 2015 | 2.8 / 3.2 FSI V6, VIN check |
| Audi | A6 C6 (4F) | 2004 – 2011 | 2.4 / 2.8 / 3.2 FSI V6 |
| Audi | A6 C6 Allroad | 2006 – 2011 | 2.8 / 3.2 FSI V6, VIN check |
| Audi | A6 C7 (4G) | 2011 – 2015 | 2.4 / 2.8 FSI V6, VIN check |
| Audi | A7 Sportback (4G) | 2010 – 2015 | 2.8 / 3.2 FSI V6, VIN check |
| Audi | Q5 (8RB) | 2008 – 2015 | 2.4 / 3.2 FSI V6, VIN check |
| Audi | A8 D3 (4E) | 2005 – 2010 | 2.8 / 3.2 FSI V6, VIN check |
| VIN check | Old unit stamped 06E103547P | All years | Direct match to this part |
| VIN check | Old unit stamped 06E103547 | All years | Earlier revision, confirm against VIN |
| VIN check | Old unit stamped 06E103547A or 06E103547E | All years | Earlier revision of the same family |
| VIN check | Catalogue ref GATES EMH9001 | All years | Same separator in aftermarket packaging |
| VIN check | Catalogue ref HENGST AS354M02 | All years | Same separator with seal in aftermarket packaging |
| VIN check | Catalogue ref VAICO V10-3502 | All years | Equivalent breather valve reference |
| Not covered | 1.8 / 2.0 TFSI four cylinder crankcase valve | All years | Different engine family |
| Not covered | 4.2 FSI V8 breather | All years | Different part number and housing |
| Not covered | 3.0 TDI V6 crankcase component | All years | Diesel application, different part |
| Not covered | Breather hose or gasket kit | All years | Ordered separately if required |
Installation notes
On these V6 engines the separator is mounted low under the intake manifold, so access usually means removing the engine cover and intake components first. Disconnect the battery only where the workshop procedure calls for it, release the breather hoses and the electrical connector, then undo the mounting fasteners evenly so the flange is not cracked. Inspect the mating surface and renew the seal if the old one is hardened or compressed; this listing supplies the separator shown in the photographs and not a separate gasket kit. Refit the hoses fully onto their necks, reconnect the connector and clear any stored fault codes after the job. Start the engine and check for a stable idle, no intake hissing and no oil smell. Because the unit is plastic, tighten the bolts only to the workshop torque figure and never lever against the hose ports or the diaphragm cover.
What is not included and what is not covered
The price is for ONE 06E103547P oil separator as photographed. NOT included: separate gasket or seal kit, breather hoses, clamps, bolts, tools, labour or intake components. NOT covered: the 1.8 and 2.0 TFSI four cylinder crankcase valves, the 4.2 FSI V8 breather, the 3.0 TDI V6 components, cars whose old unit carries a different base number until the variant has been confirmed, and damage caused by refitting hardened seals or by over tightening the plastic flange. Problems caused by incorrect hose routing, a disconnected electrical connector or faults in other engine systems are also outside the warranty.
Condition and warranty
Every separator we supply is brand new, unused and genuine OEM, carrying the moulded number and markings shown in the photographs, never a used take off and never an unbranded copy. Each unit is checked before dispatch: the housing is free of cracks, the diaphragm cover and flange ears are intact, the hose ports and connector are clean, and the part matches the number in this listing. We back it with a twelve months warranty against manufacturing defects from the date of delivery. Warranty does not cover damage from installation faults, from reusing old seals or from faults elsewhere in the crankcase ventilation system. Keep the packing until the workshop has confirmed the part fits.
Packing and shipping
The approximate packed weight is 1.1 kg including protective wrap. The separator travels with the flange and ports protected so they cannot be chipped in transit, and the customs description is motor vehicle engine part, HS 3926 or 8483 depending on the destination. Combined orders are welcome: ask us to pack this separator with breather hoses, a gasket set or other engine parts for the same car in one shipment to save on freight. Include your model year, engine code and VIN so we can recheck the number before dispatch.
Trade and wholesale supply
Three quantity tiers are available on this listing: 1 pc sample, 5 pcs and up and 20 pcs and up, with the price stepping down as the quantity rises. Workshops that maintain the 2.4, 2.8 and 3.2 FSI V6 Audi fleet keep this separator on the shelf because split diaphragms and sticking pressure valves are a recurring cause of rough idle and oil consumption on those engines. All tiers are stocked items and volume enquiries beyond the listed tiers are welcome. If you are buying for a workshop, send us the old part numbers you see most often and we will flag any application that needs a different breather family before the order is packed.
Related parts on this store
Other engine and emission parts for the same Audi V6 family are listed separately on this store; search by the part number from your old component rather than assuming that a neighbouring model year uses the same breather. No breather hose, clamp or gasket is included with this listing, and those items should be ordered separately if the originals are hardened, split or missing. If you need confirmation that 06E103547P is the right separator for your car, send us the VIN and a clear photograph of the old housing before placing the order.







